Calculation verification
Every result on this page can be checked by hand. For each calculator: the inputs, the formula, a worked example with real numbers, the units, the standard it comes from, and what it does not cover. Worked examples checked against the calculator output on 17 Nov 2026.
Branch reinforcement (area replacement)ASME B31.3 para. 304.3.3
Input parameters
| Parameter | Symbol | Unit | Source |
|---|---|---|---|
| Header and branch NPS, schedule | Dh, Th, Db, Tb | mm | ASME B36.10M / B36.19M |
| Branch angle | β | degrees | 45° to 90° |
| Design pressure | P | bar(g) → MPa | Design basis |
| Allowable stress, header and branch | Sh, Sb | MPa | B31.3 Table A-1 |
| E, W, Y | – | – | B31.3 Table A-1B, para. 302.3.5, Table 304.1.1 |
| Corrosion allowance | c | mm | Piping class |
| Mill under-tolerance | m | % | Pipe specification (12.5% seamless) |
| Reinforcing pad thickness and OD | Tr, Dp | mm | Your pad, or sized by the tool |
| Fillet weld leg | – | mm | Weld detail (optional) |
Formula used
Pressure design thickness th = P·Dh / 2(Sh·E·W + P·Y); tb = P·Db / 2(Sb·E·W + P·Y) Minimum wall T̄h = Th(1 − m); T̄b = Tb(1 − m) d₁ = [Db − 2(T̄b − c)] / sin β; d₂ = max(d₁, (T̄b − c) + (T̄h − c) + d₁/2), not more than Dh L₄ = min( 2.5(T̄h − c), 2.5(T̄b − c) + Tr ) Required A₁ = th · d₁ · (2 − sin β) A₂ = (2d₂ − d₁)(T̄h − th − c); A₃ = 2·L₄(T̄b − tb − c) / sin β (× Sb/Sh if lower) A₄ = pad (min(Dp, 2d₂) − Db/sin β)·Tr (× pad/header stress ratio) + fillet welds ½·leg² each Adequate when A₂ + A₃ + A₄ ≥ A₁
Worked example
NPS 6 Sch 40 branch at 90° on an NPS 8 Sch 40 header, carbon steel, 40 bar(g), S = 137.9 MPa, E = W = 1, Y = 0.4, c = 1.5 mm, mill tolerance 12.5%.
- Header D = 219.1, T = 8.18 → T̄h = 7.16 mm; branch D = 168.3, T = 7.11 → T̄b = 6.22 mm
- th = 4.0 × 219.1 / (2 × (137.9 + 1.6)) = 3.14 mm; tb = 4.0 × 168.3 / 279.0 = 2.41 mm
- d₁ = 168.3 − 2 × (6.22 − 1.5) = 158.8 mm; d₂ = max(158.8, 4.72 + 5.66 + 79.4) = 158.8 mm
- A₁ = 3.14 × 158.8 × (2 − 1) = 499 mm²
- A₂ = (317.7 − 158.8) × (7.16 − 3.14 − 1.5) = 400 mm²
- Without a pad: L₄ = min(14.1, 11.8) = 11.8 mm; A₃ = 2 × 11.8 × (6.22 − 2.41 − 1.5) = 55 mm²; total 454 < 499, so not enough
- With a 6 mm pad: L₄ = min(14.1, 17.8) = 14.1 mm; A₃ = 65 mm²; pad OD 220 → A₄ = (220 − 168.3) × 6 = 310 mm²
- A₂ + A₃ + A₄ = 400 + 65 + 310 = 775 mm² ≥ 499 mm²
Result: Stub-in needs a pad: 6 mm × Ø220 mm gives 155% of the required area. (A B16.9 reducing tee needs no check.)
Units
- mm and mm²; pressure in bar(g), stresses in MPa
Standard or engineering basis
- ASME B31.3 para. 304.3.3 (reinforcement of welded branch connections) and para. 304.3.2 (when no calculation is needed)
- Typical branch table practice; MSS SP-97 integrally reinforced outlets; ASME B16.9 tees
Assumptions and limitations
- Internal pressure only. External loads, thermal and occasional loads, and fatigue at the branch are not checked.
- The branch fitting suggestion is a typical branch table; your piping class branch table governs.
- Valid for β from 45° to 90°. Large branch ratios (above about 0.5), thick walls (t ≥ D/6) and high-pressure service need further analysis.
- Pads that wrap far around a small header, slotted pads, and pads of different material need the designer's judgement; vent the pad (tell-tale hole).
Contact & corrections
Questions, a value that differs from your edition of the code, or an idea for a new tool. For corrections, include the standard, table and size so the value can be checked.
Or email directly:
Isometric revision compare
Compare the issued (IFC) isometric against the latest from the model. Drop two PDFs for a linework overlay, or two PCF files for a component-by-component change list. Files stay in your browser.