Flange joint assembly
A weld neck raised-face joint to ASME B16.5 with gasket and stud bolts: stud length, gasket thickness, flange gap, target torque and the tightening sequence. Pick size, class and gasket.
Calculation verification
Every result on this page can be checked by hand. For each calculator: the inputs, the formula, a worked example with real numbers, the units, the standard it comes from, and what it does not cover. Worked examples checked against the calculator output on 17 Nov 2026.
Flange joint assemblyASME B16.5, B16.20 / B16.21, PCC-1
Input parameters
| Parameter | Symbol | Unit | Source |
|---|---|---|---|
| NPS and class | → tf, d, n | mm, in | ASME B16.5 weld neck RF |
| Gasket | tg, tc | mm | B16.20 spiral wound or B16.21 sheet |
| Threads past nut | k | threads | Project standard |
| Bolting material | Sy | MPa | ASTM A193 / A320 yield |
| Target bolt stress | % | % of yield | Assembly procedure (50% typical) |
| Nut factor | K | – | Lubricant (0.16 typical for moly paste) |
Formula used
Stud L = 2·tf + 2·RF (Class ≥ 400) + tg + 2·d + 2·k·p, rounded up to 5 mm Stress area As = 0.7854 (d − 0.9743/TPI)² (d in inch) Bolt load F = (% × Sy) × As Torque T = K · F · d Gap at raised faces = compressed gasket; gap at rims = compressed gasket + 2 × RF height Sequence: PCC-1 legacy cross pattern in groups of four opposite bolts; passes 20–30%, 50–70%, 100%, then clockwise
Worked example
NPS 4 Class 300, spiral wound 4.5 mm (≈ 3.3 mm compressed), 3 threads, A193 B7 at 50% of yield, K = 0.16.
- B16.5: tf = 30.2 mm (incl. 1.6 mm RF); 8 × 3/4″-10 UNC
- L = 60.5 + 4.5 + 38.1 + 15.2 = 118.3 → 120 mm
- As = 0.7854 × (0.75 − 0.0974)² = 0.3345 in² = 216 mm²
- Sy = 105 ksi = 724 MPa; target 362 MPa; F = 52.5 ksi × 0.3345 in² = 17 560 lbf = 78.1 kN
- T = 0.16 × 17 560 × 0.75 / 12 = 176 ft·lb = 238 N·m
- Gap at raised faces 3.3 mm; at rims 3.3 + 2 × 1.6 = 6.5 mm
Result: 8 studs 3/4″ × 120 mm, target torque 238 N·m (176 ft·lb).
Units
- mm, mm², MPa, kN, N·m with inch, lbf and ft·lb equivalents
Standard or engineering basis
- ASME B16.5 flange data; ASME B16.20 / B16.21 gaskets
- ASTM A193 / A320 yield strengths; thread stress area per ASME B1.1
- ASME PCC-1 (legacy cross pattern and passes)
Assumptions and limitations
- Torque is a planning estimate. The joint assembly procedure, gasket maker's stress limits and the actual lubricant set the final value.
- Nut factor K varies widely with lubricant and condition; 0.16 assumes a good anti-seize.
- Compressed gasket thickness is typical, not guaranteed.
- RTJ, lens and non-B16.5 flanges are not covered.
Contact & corrections
Questions, a value that differs from your edition of the code, or an idea for a new tool. For corrections, include the standard, table and size so the value can be checked.
Or email directly:
Isometric revision compare
Compare the issued (IFC) isometric against the latest from the model. Drop two PDFs for a linework overlay, or two PCF files for a component-by-component change list. Files stay in your browser.