Piping glossary: terms and abbreviations
395 piping terms and abbreviations used in design, drawings, materials, valves, supports, testing and EPC projects, from FOT and BOP to HPV, FFW and PWHT. Each entry links to the page that covers it in detail.
No terms match. Try a shorter word, or suggest a term.
#
- 40S / 80SStainless schedulesPipe and fittings
- Schedules from ASME B36.19M for stainless steel pipe. Mostly the same as Sch 40/80 but differ at some sizes. Pipe →
A
- A105ASTM A105Materials and welding
- Carbon steel forgings for flanges and forged fittings. Flanges →
- A106 Gr BASTM A106Materials and welding
- Seamless carbon steel pipe for high-temperature service. Pipe →
- A182ASTM A182Materials and welding
- Alloy and stainless forgings, such as F316L, F11, F22. Flanges →
- A234 WPBASTM A234Materials and welding
- Carbon steel butt-weld fittings. Butt-weld fittings →
- A312ASTM A312Materials and welding
- Stainless steel pipe, seamless and welded. Pipe →
- A333 Gr 6ASTM A333Materials and welding
- Low-temperature carbon steel pipe. Pipe →
- A335ASTM A335Materials and welding
- Seamless alloy steel pipe for high temperature (P11, P22, P91). Pipe →
- A350 LF2ASTM A350Materials and welding
- Low-temperature carbon steel forgings. Flanges →
- A403ASTM A403Materials and welding
- Stainless steel butt-weld fittings (WP304, WP316). Butt-weld fittings →
- ActuatorValves
- Device that operates a valve: pneumatic, hydraulic or electric. Control valves →
- AFCApproved For ConstructionDrawings and 3D
- Another name for IFC.
- AnchorLayout and supports
- Support fixing the pipe in all directions. Pipe supports →
- APIAmerican Petroleum InstituteCodes and bodies
- Standards for oil and gas equipment: valves, pumps, tanks.
- API 5LMaterials and welding
- Line pipe specification (Gr B, X52, X65 and so on). Pipe →
- API 600 / 602Codes and bodies
- Steel gate valves / small forged valves. Valves →
- API 609Codes and bodies
- Butterfly valves. Valves →
- API 610Codes and bodies
- Centrifugal pumps for petroleum industries, including allowable nozzle loads.
- API 650Codes and bodies
- Welded steel storage tanks.
- API 6DValves
- Specification for pipeline valves.
- ASAlloy SteelMaterials and welding
- Chrome-moly steel such as P11, P22, P91 for high temperature. Pipe →
- As-builtDrawings and 3D
- Drawing updated to show what was actually installed.
- ASMEAmerican Society of Mechanical EngineersCodes and bodies
- Publishes the B31 piping codes and B16 component standards.
- ASME Section IXBPVC IXCodes and bodies
- Welding and brazing qualifications.
- ASME Section VIIIBPVC VIIICodes and bodies
- Pressure vessel code.
- ASTMASTM InternationalCodes and bodies
- Publishes material specifications (A106, A105 and so on).
B
- B16.10ASME B16.10Codes and bodies
- Face-to-face and end-to-end dimensions of valves. Valves →
- B16.11ASME B16.11Codes and bodies
- Forged socket-weld and threaded fittings. Socket weld & NPT →
- B16.20 / B16.21Codes and bodies
- Metallic / non-metallic gaskets for pipe flanges. Gaskets →
- B16.25ASME B16.25Codes and bodies
- Butt-welding end preparation. Butt-weld fittings →
- B16.47ASME B16.47Codes and bodies
- Large-diameter steel flanges, NPS 26 to 60. Large flanges B16.47 →
- B16.48ASME B16.48Codes and bodies
- Line blanks (spectacle blinds, spades and spacers). Figure-8 & paddle →
- B16.5ASME B16.5Codes and bodies
- Pipe flanges and flanged fittings, NPS ½ to 24. Flanges →
- B16.9ASME B16.9Codes and bodies
- Factory-made butt-weld fittings. Butt-weld fittings →
- B31.1ASME B31.1Codes and bodies
- Power piping code.
- B31.3ASME B31.3Codes and bodies
- Process piping code for refineries, chemical and related plants. Branch reinforcement →
- B31.4 / B31.8Codes and bodies
- Codes for liquid pipelines / gas transmission and distribution.
- B36.10M / B36.19MCodes and bodies
- Dimensions of welded and seamless steel pipe / stainless steel pipe. Pipe →
- B7 / 2HASTM A193 B7 / A194 2HFlanges and bolting
- The common carbon-alloy stud bolt and heavy hex nut grades. Flange joint →
- Ball valveValves
- Quarter-turn valve with a bored ball; quick on/off. Valves →
- barg / psigGauge pressureProcess and instruments
- Pressure above atmospheric; bara and psia are absolute. P–T ratings →
- Basic engineeringProject and general
- Process design phase producing PFDs, P&IDs and datasheets.
- Battery limitBLDrawings and 3D
- Boundary between units or between contractor and client scope.
- BC / PCDBolt Circle / Pitch Circle DiameterFlanges and bolting
- Diameter of the circle through the centres of the bolt holes. Flanges →
- BDVBlowdown ValveValves
- Valve that opens to depressurise equipment to flare in an emergency. Control valves →
- BEBevelled EndPipe and fittings
- Pipe or fitting end machined to a weld bevel (usually 37.5°) for butt welding. Butt-weld fittings →
- BLBlind flangeFlanges and bolting
- Solid flange closing a flanged end or nozzle. Flanges →
- BlastingSa 2½Testing and construction
- Abrasive blast cleaning of steel before painting, to a standard grade.
- BlowdownProcess and instruments
- Depressurising equipment to flare, or draining boiler water to control solids.
- BlowingSteam blowingTesting and construction
- Cleaning steam lines with high-velocity steam before start-up.
- Bolt tensioningFlanges and bolting
- Tightening bolts by stretching them hydraulically instead of with torque; used on large or critical joints. Flange joint →
- Bolt torqueFlanges and bolting
- Tightening torque applied to flange bolts to reach the target bolt stress. Flange joint →
- BOMBill Of MaterialsDrawings and 3D
- List of all components on a drawing with size, description and quantity. Isometric symbols →
- BOPBottom Of PipeLayout and supports
- Elevation of the underside of a pipe, used on racks. Pipe rack →
- Branch tablePipe and fittings
- Table in the piping class that sets which branch fitting to use for each run and branch size. Branch reinforcement →
- Brownfield / GreenfieldProject and general
- Project in an existing plant / on a new site.
- BSPBritish Standard Pipe threadPipe and fittings
- Pipe thread standard used in the UK and Europe; BSPT is tapered, BSPP is parallel. Socket weld & NPT →
- Bundle pullLayout and supports
- Clear area in front of a heat exchanger for removing the tube bundle. Access & maintenance →
- Butterfly valveValves
- Quarter-turn valve with a disc on a shaft; compact for large sizes (API 609). Valves →
- BWButt WeldPipe and fittings
- A full-penetration weld joining two bevelled ends; the standard joint for process piping. Butt-weld fittings →
- BypassValves
- Line around a control valve or equipment, usually with a globe valve, to keep running during maintenance. Control valves →
C
- CACorrosion AllowanceMaterials and welding
- Extra wall thickness added for corrosion over the plant life. Pipe →
- Cable trayLayout and supports
- Tray carrying electrical and instrument cables, often on the pipe rack. Pipe rack →
- CAESAR IIDrawings and 3D
- Pipe stress analysis software by Hexagon. Expansion loops →
- CAFCompressed Asbestos-Free fibreFlanges and bolting
- Sheet gasket material for low-pressure utilities (ASME B16.21). Gaskets →
- CapPipe and fittings
- Butt-weld fitting closing the end of a pipe. Butt-weld fittings →
- CavitationProcess and instruments
- Vapour bubbles forming and collapsing in a liquid, damaging pumps and valves.
- Chain wheelChain operatorValves
- Wheel and chain that let a high valve be operated from below. Valve access →
- Check valveNon-return valveValves
- Valve that lets flow go one way only. Valves →
- CladdingMaterials and welding
- A layer of corrosion-resistant alloy bonded to carbon steel.
- Clash checkDrawings and 3D
- Check for physical interference in the 3D model.
- ClassPressure classFlanges and bolting
- Flange rating designation (150, 300, 600, 900, 1500, 2500). The allowable pressure depends on material and temperature. P–T ratings →
- Claus processProject and general
- Process converting H2S to elemental sulphur in a thermal reactor and catalytic converters.
- CL / COPCentreline / Centre Of PipeLayout and supports
- Elevation or line through the centre of a pipe. Pipe rack →
- ClearanceLayout and supports
- Clear space between pipes, steel and equipment for access, insulation and movement. Pipe spacing →
- Cold springLayout and supports
- Deliberately cutting a line short and pulling it into place to reduce hot loads; used with care. Expansion loops →
- CommissioningTesting and construction
- Bringing the plant into operation with process fluids.
- CondensateProcess and instruments
- Water formed when steam gives up heat.
- Confined spaceTesting and construction
- Enclosed space such as a vessel, needing special entry controls.
- Constant springLayout and supports
- Spring support giving nearly constant load over large movements. Pipe supports →
- ContinuationDrawings and 3D
- Note that a line continues on another isometric or drawing. Isometric symbols →
- Control valveCVValves
- Valve that modulates flow automatically from a control signal. Control valves →
- CoordinatesN / EDrawings and 3D
- Plant grid position of a point (northing and easting). Isometric symbols →
- CouplingPipe and fittings
- Socket-weld or threaded fitting joining two small-bore pipes; a half coupling is welded to a run as a branch. Socket weld & NPT →
- CPVC / PVCMaterials and welding
- Plastic pipe for chemicals and utilities at low pressure and temperature.
- CRACorrosion Resistant AlloyMaterials and welding
- Collective term for stainless, duplex and nickel alloys.
- CrossPipe and fittings
- Four-way fitting; rare in process piping. Butt-weld fittings →
- CSCarbon SteelMaterials and welding
- The most common piping material, such as A106 Gr B pipe and A105 flanges. Pipe →
- CSO / CSCCar Sealed Open / ClosedValves
- Valve sealed in position so it cannot be operated without breaking the seal. P&ID symbols →
- CUICorrosion Under InsulationMaterials and welding
- Corrosion of pipe surfaces under wet insulation, a major cause of leaks.
- Cut lengthDrawings and 3D
- Length of a straight pipe piece cut for a spool, listed in the cut list. Isometric symbols →
D
- DatasheetProject and general
- Document giving the design data and requirements of an item. Equipment data check →
- DBBDouble Block and BleedValves
- Two isolating seats with a bleed between them, for positive isolation. Valves →
- DCN / ECNDesign / Engineering Change NoticeProject and general
- Document recording a design change.
- DCSDistributed Control SystemProcess and instruments
- Plant control system.
- Dead legLayout and supports
- Section of pipe with no flow, where corrosion and freezing can occur.
- DeflectionSagLayout and supports
- Vertical sag of a pipe between supports, usually limited to 2.5–5 mm. Support spans →
- Design pressureDPProcess and instruments
- Highest pressure the piping is designed for, with its coincident temperature. P–T ratings →
- Design temperatureDTProcess and instruments
- Highest (or lowest) metal temperature used for design. P–T ratings →
- Detailed engineeringDEProject and general
- Phase producing all drawings and documents for procurement and construction.
- Diaphragm valveValves
- Valve where a flexible diaphragm closes against a weir; used for corrosive or clean service. Valves →
- Displacement stressExpansion stress rangeLayout and supports
- Stress from restrained thermal movement; secondary and self-limiting. Expansion loops →
- DNDiamètre NominalPipe and fittings
- Metric size designation (DN 50 = NPS 2, DN 150 = NPS 6). A label only; the real OD comes from the pipe standard. Pipe →
- Drip legLayout and supports
- Pocket at a low point of steam lines where condensate collects to a trap.
- DSSDuplex Stainless SteelMaterials and welding
- Stainless steel with mixed austenite and ferrite; stronger and more resistant to chloride cracking.
- Dual plate checkWafer checkValves
- Compact check valve with two spring-loaded half plates, fitted between flanges. Valves →
- Dummy legLayout and supports
- Pipe stub welded to an elbow to carry the line to a support. Pipe weight & loads →
E
- E3D / PDMSAVEVA Everything3D / Plant Design Management SystemDrawings and 3D
- AVEVA 3D plant design software; E3D replaced PDMS.
- Eccentric reducerPipe and fittings
- Reducer with one side flat, so top or bottom of pipe stays in line. Butt-weld fittings →
- EFWElectric Fusion WeldedPipe and fittings
- Pipe welded along its seam by fusion welding, usually for larger sizes and stainless. Pipe →
- ELElevationLayout and supports
- Height relative to the plant datum. Isometric symbols →
- ElboletPipe and fittings
- Olet shaped to fit on an elbow, for thermowells or drains. Branch reinforcement →
- ElbowPipe and fittings
- A fitting that changes direction, usually 90° or 45°, butt-weld to ASME B16.9. Butt-weld fittings →
- EN / ISOEuropean / International standardsCodes and bodies
- Standards such as EN 1092-1 flanges and ISO 15649 process piping.
- EPCEngineering, Procurement and ConstructionProject and general
- Contract where one contractor designs, buys and builds the plant.
- EPCMEPC ManagementProject and general
- Contractor manages engineering, procurement and construction on behalf of the owner.
- ErectionTesting and construction
- Installing spools and components on site.
- ERWElectric Resistance WeldedPipe and fittings
- Pipe formed from strip and welded along its length by electric resistance, without filler. Pipe →
- Escape routeLayout and supports
- Clear path from any working area to a safe place. Access & maintenance →
- ESDV / ESVEmergency Shutdown ValveValves
- Valve that closes automatically to isolate a section in an emergency. Control valves →
- Expansion jointBellowsPipe and fittings
- Flexible element that absorbs movement in a line; needs anchors and guides designed around it. Expansion loops →
- Expansion loopLayout and supports
- U-shaped offset that absorbs thermal growth by bending. Expansion loops →
- Extension spindleValves
- Extended stem that lets a valve be operated from a platform or above grade. Valve access →
F
- Face-to-faceFTFValves
- Length of a valve between its end faces (ASME B16.10). Valves →
- FEEDFront-End Engineering DesignProject and general
- Phase defining the project before detailed engineering.
- FE / FTFlow Element / TransmitterProcess and instruments
- Primary flow device (orifice, venturi, meter) and its transmitter. P&ID symbols →
- FFFlat FaceFlanges and bolting
- Flange facing without a raised face; used against cast iron or non-metallic flanges. Flanges →
- FFWField Fit WeldDrawings and 3D
- Field weld where the pipe is supplied extra long to be cut to fit on site. Isometric symbols →
- Fit-upTesting and construction
- Aligning and tacking parts before welding.
- FlareProcess and instruments
- System collecting and burning relief and blowdown gases safely.
- FlashingProcess and instruments
- Liquid turning partly to vapour as its pressure drops.
- FlexibilityLayout and supports
- Ability of a routing to absorb thermal movement without overstress. Expansion loops →
- Flow rateProcess and instruments
- Volume or mass of fluid passing per unit time.
- FlushingTesting and construction
- Cleaning the inside of piping with water or air after erection.
- FOBFlat On BottomPipe and fittings
- Eccentric reducer orientation keeping bottom of pipe level; used on racks and sleepers. Butt-weld fittings →
- FOTFlat On TopPipe and fittings
- Eccentric reducer orientation keeping top of pipe level; used at pump suctions to avoid vapour pockets. Butt-weld fittings →
- Future spaceLayout and supports
- Spare rack width reserved for future lines, often 20–25%. Pipe rack →
- FWField WeldDrawings and 3D
- Weld made on site during erection. Isometric symbols →
G
- GAGeneral ArrangementDrawings and 3D
- Plan and section drawing of an area or item showing layout and dimensions.
- GalvanisedMaterials and welding
- Steel coated with zinc for corrosion protection, used for water and air utilities.
- GasketFlanges and bolting
- Seal between two flange faces. Gaskets →
- Gate valveValves
- Isolation valve with a wedge moving across the flow; fully open or closed only. Valves →
- Gear operatorValves
- Gearbox fitted to a large valve to reduce operating effort. Valve access →
- Globe valveValves
- Valve with a disc moving onto a seat; used for throttling. Valves →
- GMAW / FCAWGas Metal / Flux Cored Arc WeldingMaterials and welding
- Wire-fed welding processes used in shops.
- GRP / GREGlass Reinforced Plastic / EpoxyMaterials and welding
- Composite pipe used for cooling water, seawater and drains.
- GTAW / TIGGas Tungsten Arc WeldingMaterials and welding
- Precise welding process, often used for root passes.
- GuideLayout and supports
- Support restraining sideways movement while allowing axial sliding. Pipe supports →
H
- HandoverProject and general
- Transfer of the completed plant and documents to the owner.
- HangerRod hangerLayout and supports
- Support hanging the pipe from steel above. Pipe supports →
- Hardness testTesting and construction
- Check that weld and HAZ hardness are within limits, especially for sour service and PWHT.
- HAZHeat Affected ZoneMaterials and welding
- Base metal next to a weld whose structure is changed by welding heat.
- HAZOPHazard and Operability studyProcess and instruments
- Structured review of P&IDs to find hazards and operating problems.
- HDPEHigh Density PolyethyleneMaterials and welding
- Plastic pipe for buried water and drain lines.
- HeadroomLayout and supports
- Clear height above walkways and platforms, usually at least 2.1 m. Access & maintenance →
- Heat numberMaterials and welding
- Identification of the melt a material came from; traced from MTC to the component.
- Heat tracingLayout and supports
- Steam (ST) or electric (ET) heating along a pipe to stop freezing or keep fluid hot. Isometric symbols →
- HICHydrogen Induced CrackingMaterials and welding
- Cracking of steel in wet H2S service caused by absorbed hydrogen.
- HOLDDrawings and 3D
- Mark on a drawing for unconfirmed information; held items are not fabricated. Isometric symbols →
- HoseFlexible hosePipe and fittings
- Flexible connection for loading points or vibrating equipment.
- Hot workTesting and construction
- Work producing sparks or flame, such as welding, needing a permit.
- HPP / FGLHigh Point of Paving / Finished Grade LevelLayout and supports
- Reference elevations for the ground or paving.
- HPVHigh Point VentLayout and supports
- Vent at the high point of a line. Isometric symbols →
- HSEHealth, Safety and EnvironmentProject and general
- The discipline and rules for safe working.
- HydrotestHydrostatic testTesting and construction
- Pressure test with water at 1.5 × design pressure (B31.3, temperature corrected).
I
- IBRIndian Boiler RegulationsCodes and bodies
- Indian regulations for steam boilers and steam piping.
- IDInside DiameterPipe and fittings
- The bore of a pipe: OD minus twice the wall thickness. Pipe →
- IFCIssued For ConstructionDrawings and 3D
- Revision status allowing work on site.
- IFR / IFAIssued For Review / ApprovalDrawings and 3D
- Revision status sent to client for comments or approval.
- Instrument tagProcess and instruments
- Identifier of an instrument, such as PT-101, built from ISA-5.1 letters. P&ID symbols →
- Insulating kitFlange isolation kitFlanges and bolting
- Gasket, sleeves and washers that electrically isolate a flange joint for cathodic protection. Gaskets →
- InsulationLayout and supports
- Thermal or acoustic cladding on pipe for heat conservation, personnel protection or cold service. Pipe spacing →
- Interdisciplinary checkIDCProject and general
- Review of a document by other disciplines before issue.
- InterlockProcess and instruments
- Automatic action preventing an unsafe condition.
- ISA-5.1Process and instruments
- Standard for instrument symbols and identification letters. P&ID symbols →
- ISBLInside Battery LimitsProject and general
- Facilities inside a process unit boundary.
- ISOIsometric drawingDrawings and 3D
- Drawing of one line in isometric projection with dimensions and BOM, for fabrication. Isometric symbols →
- IsogenDrawings and 3D
- Software that generates isometric drawings automatically from the 3D model. Isometric symbols →
J
- Jacketed pipePipe and fittings
- Pipe inside a larger pipe, with steam or hot oil in the annulus to keep the process fluid hot, such as for sulphur.
K
- KammprofileFlanges and bolting
- Grooved metal gasket with graphite or PTFE layers, used for heat exchangers and difficult joints. Gaskets →
- Knife gate valveValves
- Gate valve with a thin sharp gate, for slurries and solids. Valves →
- Knockout drumKODProcess and instruments
- Vessel separating liquid from gas, for example before a compressor or flare.
L
- L7 / B8Flanges and bolting
- Low-temperature (A320 L7) and stainless (A193 B8) bolt grades. Flange joint →
- LateralPipe and fittings
- Fitting with the branch at 45° (or another angle) to the run. Branch reinforcement →
- LatroletPipe and fittings
- Olet for a 45° lateral branch. Branch reinforcement →
- Lead timeProject and general
- Time from order to delivery; long-lead items are ordered early.
- LG / LTLevel Gauge / TransmitterProcess and instruments
- Level instruments on vessels and tanks. P&ID symbols →
- L gradeLow carbonMaterials and welding
- Stainless grades such as 304L and 316L with carbon ≤ 0.03%, for better weld corrosion resistance.
- LicensorProject and general
- Company owning a process technology and supplying its design package.
- Line blindFlanges and bolting
- Any plate inserted between flanges to isolate a line (ASME B16.48). Figure-8 & paddle →
- Line listLDT, Line Designation TableDrawings and 3D
- Table of every line with size, fluid, class, design data, test and insulation.
- Line numberDrawings and 3D
- Unique identifier of a line, usually size, service, number, class and insulation code. P&ID symbols →
- Line stopAxial stopLayout and supports
- Support stopping axial movement in one or both directions. Pipe supports →
- LiningMaterials and welding
- Non-metallic lining (PTFE, rubber, cement) inside pipe for corrosive service.
- LJLap Joint flangeFlanges and bolting
- Loose flange used with a stub end; turns freely to align bolt holes. Flanges →
- LO / LCLocked Open / Locked ClosedValves
- Valve fixed in position with a lock or car seal, shown on the P&ID. P&ID symbols →
- LOTOLock Out Tag OutTesting and construction
- Procedure isolating energy sources before work.
- LPDLow Point DrainLayout and supports
- Drain at the low point of a line. Isometric symbols →
- LR elbowLong Radius elbowPipe and fittings
- Elbow with centre-to-end of 1.5 × NPS. The default choice. Butt-weld fittings →
- LTCSLow Temperature Carbon SteelMaterials and welding
- Carbon steel impact tested for low temperature, such as A333 Gr 6 and A350 LF2. Pipe →
- LWNLong Weld NeckFlanges and bolting
- Weld neck flange with an extended neck, used as a nozzle. Flanges →
M
- Maintenance accessLayout and supports
- Space reserved for removing and repairing equipment, valves and instruments. Access & maintenance →
- Match lineDrawings and 3D
- Line on a drawing where it continues on another drawing.
- Material groupFlanges and bolting
- Group in ASME B16.5 (for example 1.1 for A105) that sets which P–T table applies. P–T ratings →
- MAWPMaximum Allowable Working PressureProcess and instruments
- Highest pressure a vessel can safely operate at, at its design temperature.
- MDR / MDLMaster Document Register / ListProject and general
- List of all project documents and their status.
- Mechanical completionMCTesting and construction
- Stage when construction is complete and checked, ready for pre-commissioning.
- Mill toleranceMaterials and welding
- Allowed under-thickness of pipe from manufacture, usually 12.5%. Pipe →
- Mitre bendPipe and fittings
- A change of direction made by welding angled cuts of pipe; used for large low-pressure lines. Butt-weld fittings →
- MOCManagement Of ChangeProject and general
- Procedure for reviewing and approving changes.
- Model review30/60/90%Drawings and 3D
- Formal multi-discipline review of the 3D model at defined stages.
- MOVMotor Operated ValveValves
- Valve with an electric motor actuator. Control valves →
- MR / POMaterial Requisition / Purchase OrderProject and general
- Technical request for quotation / the order placed with a vendor.
- MSSManufacturers Standardization SocietyCodes and bodies
- Publishes MSS SP standards for valves, fittings and supports.
- MSS SP-58Codes and bodies
- Pipe hangers and supports: materials, design and types. Pipe supports →
- MSS SP-97Codes and bodies
- Integrally reinforced forged branch outlet fittings (olets). Branch reinforcement →
- MTCMaterial Test CertificateMaterials and welding
- Mill certificate showing heat number, chemistry and mechanical tests (EN 10204 3.1/3.2).
- MT / MPIMagnetic Particle TestingTesting and construction
- Surface crack inspection for magnetic materials.
- MTOMaterial Take-OffDrawings and 3D
- List of piping materials quantities for procurement. MTO calculator →
N
- NACENACE MR0175 / ISO 15156Materials and welding
- Requirements for materials in sour (H2S) service to prevent sulfide stress cracking.
- NDE / NDTNon-Destructive Examination / TestingTesting and construction
- Inspection of welds and materials without damaging them.
- Needle valveValves
- Small valve with a fine tapered stem, used on instrument lines. Valves →
- NFPANational Fire Protection AssociationCodes and bodies
- US fire protection codes, including fire water systems.
- NipoletPipe and fittings
- One-piece olet with an integral nipple, for vents and drains. Branch reinforcement →
- NipplePipe and fittings
- Short length of small-bore pipe, plain or threaded, used between fittings. Socket weld & NPT →
- NO / NCNormally Open / Normally ClosedValves
- The normal operating position of a valve. P&ID symbols →
- North arrowPlant northDrawings and 3D
- Arrow fixing directions on plans and isos; plant north may differ from true north. Isometric symbols →
- Nozzle loadLayout and supports
- Forces and moments from piping on an equipment nozzle, checked against allowable values. Equipment data check →
- Nozzle orientationLayout and supports
- Drawing fixing angle, elevation and projection of each nozzle on a vessel. Equipment data check →
- NPSNominal Pipe SizePipe and fittings
- The size designation of pipe in inches. From NPS 14 up the OD equals the NPS; below that the OD is fixed by ASME B36.10M and differs from the number. Pipe →
- NPSHNet Positive Suction HeadProcess and instruments
- Margin above vapour pressure at a pump suction; NPSHa must exceed NPSHr.
- NPTNational Pipe Taper threadPipe and fittings
- The tapered pipe thread used in the US (ASME B1.20.1), sealing on the thread. Socket weld & NPT →
- NRVNon-Return ValveValves
- Another name for a check valve. Valves →
O
- ODOutside DiameterPipe and fittings
- The outside diameter of a pipe or component. For ASME pipe it stays the same for every schedule. Pipe →
- OffsetSkewDrawings and 3D
- Line not running along a main axis; shown with a hatched triangle on isos. Isometric symbols →
- OffsitesOSBLProject and general
- Facilities outside the process units: tanks, utilities, flare, pipe racks.
- OISDOil Industry Safety DirectorateCodes and bodies
- Indian safety standards for oil and gas plants, including layout distances.
- OletBranch outlet fittingPipe and fittings
- Forged branch fitting welded to the run with integral reinforcement (MSS SP-97). Branch reinforcement →
- O&MOperation and MaintenanceProject and general
- Running and maintaining the plant after handover.
- Operating pressureProcess and instruments
- Normal working pressure in service.
- Orifice flangeFlanges and bolting
- Flange pair with pressure taps for an orifice plate. Flanges →
- Orifice plateProcess and instruments
- Plate with a hole between flanges, creating a pressure drop to measure flow. P&ID symbols →
- Owner / ClientProject and general
- Company that will own and operate the plant.
P
- Painting systemTesting and construction
- Specified surface preparation and coating layers for a service and temperature.
- PassivationTesting and construction
- Chemical treatment restoring the protective layer on stainless steel.
- PAUTPhased Array Ultrasonic TestingTesting and construction
- Advanced UT that can replace radiography.
- PCC-1ASME PCC-1Flanges and bolting
- Guidelines for assembling bolted flange joints: tightening sequence, torque and gasket handling. Flange joint →
- PCFPiping Component FileDrawings and 3D
- Text file describing a piping line component by component, used to make isos. Iso compare →
- PEPlain EndPipe and fittings
- Pipe end cut square, used for socket-weld and slip-on joints. Pipe →
- PEDPressure Equipment DirectiveCodes and bodies
- EU law for pressure equipment, including piping.
- PFDProcess Flow DiagramDrawings and 3D
- Simplified diagram of main process flows and equipment, with heat and mass balance. P&ID symbols →
- PicklingTesting and construction
- Chemical cleaning to remove scale, for example on compressor and lube oil lines.
- P&IDPiping and Instrumentation DiagramDrawings and 3D
- Schematic showing every line, valve, instrument and control loop. Not to scale. P&ID symbols →
- Pipe bendPipe and fittings
- A bend formed from straight pipe (often 3D or 5D radius) instead of a fitting; used for pigging and lower pressure drop. Butt-weld fittings →
- Pipe rackLayout and supports
- Structure carrying pipes, cable trays and sometimes air coolers between units. Pipe rack →
- Pipe spacingLayout and supports
- Centre-to-centre distance between pipes on a rack, from OD, flanges and insulation. Pipe spacing →
- Pipe supportLayout and supports
- Structure or device carrying the weight and controlling movement of a pipe. Pipe supports →
- Pipe way / SleeperLayout and supports
- Low-level concrete or steel supports carrying pipes near grade. Pipe rack →
- Pipe weightLayout and supports
- Weight of pipe, contents and insulation per metre, for support loads. Pipe weight & loads →
- Piping classPipe specDrawings and 3D
- Specification sheet setting materials, ratings, thicknesses and components for a service range.
- PI / PTPressure Indicator / TransmitterProcess and instruments
- Local pressure gauge / transmitter sending a signal to the control system. P&ID symbols →
- Plant 3DAutoCAD Plant 3DDrawings and 3D
- Autodesk 3D plant design software.
- PlatformLayout and supports
- Raised floor giving access to valves, instruments and equipment. Access & maintenance →
- Plot planLayout and supports
- Scaled layout of a unit or plant showing equipment, roads, racks and buildings.
- PlugPipe and fittings
- Threaded fitting closing a threaded end, such as a vent or drain. Socket weld & NPT →
- Plug valveValves
- Quarter-turn valve with a tapered or cylindrical plug; used for slurries and isolation. Valves →
- PMCProject Management ConsultantProject and general
- Consultant managing the project for the owner.
- PMIPositive Material IdentificationMaterials and welding
- On-site check of alloy composition, usually by XRF.
- PMSPiping Material SpecificationDrawings and 3D
- Document containing all the piping classes for a project.
- Pneumatic testTesting and construction
- Pressure test with air or gas at 1.1 × design pressure (B31.3); needs extra safety measures.
- PocketLayout and supports
- Low point in a gas line or high point in a liquid line where liquid or gas collects.
- POE / PBEPlain One End / Both EndsPipe and fittings
- Description of nipples and swages with plain (socket-weld) ends. Socket weld & NPT →
- PPPersonnel ProtectionLayout and supports
- Insulation or guards to stop people touching hot surfaces.
- PQRProcedure Qualification RecordMaterials and welding
- Record of test welds that qualify a WPS.
- Pre-commissioningTesting and construction
- Cleaning, testing and checks done before introducing process fluids.
- PreheatMaterials and welding
- Heating the joint before welding to avoid cracking in thick or alloy steel.
- Pressure dropΔPProcess and instruments
- Loss of pressure along a line from friction and fittings.
- PRVPressure Relief ValveValves
- Relief valve, usually for liquids, opening in proportion to overpressure. Valves →
- PSVPressure Safety ValveValves
- Valve that opens automatically to relieve overpressure. Valves →
- PTFE slide plateLayout and supports
- Low-friction plates under shoes to reduce friction loads. Pipe supports →
- PT (inspection)Penetrant TestingTesting and construction
- Dye penetrant inspection for surface cracks.
- P–T ratingPressure–Temperature ratingFlanges and bolting
- The allowable working pressure of a flange or valve at a given temperature for its material group (ASME B16.5). P–T ratings →
- PTWPermit To WorkTesting and construction
- Written authorisation for hazardous work on site.
- Punch listTesting and construction
- List of incomplete or defective items to fix before handover.
- PWHTPost Weld Heat TreatmentMaterials and welding
- Heating a weld after welding to relieve residual stress and temper hard zones.
R
- RedlineMarkupDrawings and 3D
- Hand or digital markup of changes on a drawing.
- ReducerPipe and fittings
- Fitting connecting two pipe sizes, concentric (same centreline) or eccentric (offset). Butt-weld fittings →
- Reinforcing padRepadPipe and fittings
- Plate ring welded around a stub-in branch to replace metal removed from the header. Branch reinforcement →
- ReinstatementTesting and construction
- Refitting items removed for testing, such as instruments and PSVs.
- Reserved volumeDrawings and 3D
- Space modelled as a block to keep areas clear for access or removal. Access & maintenance →
- RestResting supportLayout and supports
- Support carrying weight only; pipe slides freely. Pipe supports →
- Return180° bend fittingPipe and fittings
- A U-shaped fitting turning the flow back on itself, in long or short radius. Butt-weld fittings →
- Revision cloudDrawings and 3D
- Cloud drawn round changed items, tagged with the revision number. Isometric symbols →
- RFRaised FaceFlanges and bolting
- Flange facing with a raised ring where the gasket sits; the most common facing. Flanges →
- RFIRequest For InformationProject and general
- Formal question to another party, often from site.
- Ring gasketFlanges and bolting
- Oval or octagonal metal ring for RTJ flanges (R, RX, BX types). Gaskets →
- Root passMaterials and welding
- The first weld pass at the bottom of the joint.
- RTRadiographic TestingTesting and construction
- X-ray or gamma-ray inspection of welds.
- RTJRing Type JointFlanges and bolting
- Flange facing with a groove for a metal ring gasket; for high pressure and temperature. Gaskets →
- Rupture discBursting discValves
- Thin membrane that bursts at a set pressure to relieve overpressure; single use.
S
- S3D / SP3DSmart 3DDrawings and 3D
- Hexagon 3D plant design software.
- SaddleLayout and supports
- Curved plate support for large-diameter or thin-wall pipe. Pipe supports →
- SAW / LSAW / HSAWSubmerged Arc WeldedPipe and fittings
- Large-diameter pipe welded by submerged arc: L for longitudinal seam, H for helical (spiral). Pipe →
- ScaffoldingTesting and construction
- Temporary access structure for construction.
- SCCStress Corrosion CrackingMaterials and welding
- Cracking under combined tensile stress and a corrosive environment (for example chlorides on stainless).
- SchSchedulePipe and fittings
- A wall-thickness series in ASME B36.10M / B36.19M, such as Sch 40, 80 or 160. Pipe →
- SDSSSuper Duplex Stainless SteelMaterials and welding
- Higher-alloy duplex for seawater and severe service.
- SDVShutdown ValveValves
- Automated isolation valve tripped by the safety system. Control valves →
- Series A / Series BFlanges and bolting
- The two sets of ASME B16.47 large flanges (NPS 26–60). They have different bolting and will not mate. Large flanges B16.47 →
- Service testIn-service leak testTesting and construction
- Leak test at operating conditions, allowed for some low-hazard services.
- Set pressureProcess and instruments
- Pressure at which a relief valve starts to open.
- ShoeLayout and supports
- Welded or clamped piece lifting the pipe off the steel, for insulated lines. Shoe spool length →
- Shutdown / TurnaroundProject and general
- Planned stop of a plant for inspection, maintenance and tie-ins.
- SIFStress Intensification FactorLayout and supports
- Factor raising the calculated stress at fittings such as elbows and tees. Branch reinforcement →
- SILSafety Integrity LevelProcess and instruments
- Reliability level required of a safety function (SIL 1–4).
- SIS / ESDSafety Instrumented System / Emergency ShutdownProcess and instruments
- Independent safety system that trips the plant to a safe state.
- SlopeFallLayout and supports
- Drop of a line in the flow direction, for example 1:200, so it drains. Isometric symbols →
- Slug flowProcess and instruments
- Two-phase flow with large liquid slugs that hit bends and supports.
- SMAWShielded Metal Arc WeldingMaterials and welding
- Stick welding with coated electrodes; common for fill and cap passes.
- SMLSSeamlessPipe and fittings
- Pipe made without a weld seam, by piercing a billet. Pipe →
- SnubberShock absorberLayout and supports
- Device restraining sudden dynamic movement but allowing slow thermal movement. Pipe supports →
- SOSlip-On flangeFlanges and bolting
- Flange slipped over the pipe and fillet welded inside and out. Flanges →
- SockoletPipe and fittings
- Olet with a socket-weld branch end. Branch reinforcement →
- SORStatement Of RequirementsProject and general
- Owner document stating what the plant must do.
- Spade / SpacerPaddle blind / ring spacerFlanges and bolting
- Separate blank and ring used instead of a spectacle blind on large sizes. Figure-8 & paddle →
- Spec breakClass breakDrawings and 3D
- Point where the piping class changes, at a flange or valve. Isometric symbols →
- Spectacle blindFigure-8 blindFlanges and bolting
- Plate with a blank and a spacer joined by a web, fitted between flanges for positive isolation. Figure-8 & paddle →
- SpoolPipe and fittings
- Shop-fabricated piece of piping between field joints. Iso compare →
- Spool drawingDrawings and 3D
- Drawing of a single shop spool for fabrication. Isometric symbols →
- Spring supportLayout and supports
- Variable or constant spring support for lines that move vertically. Pipe supports →
- Squad checkProject and general
- Another name for interdisciplinary check.
- SR elbowShort Radius elbowPipe and fittings
- Elbow with centre-to-end of 1.0 × NPS, used where space is tight. Butt-weld fittings →
- SRUSulphur Recovery UnitProject and general
- Unit recovering sulphur from H2S gas, usually by the Claus process.
- SSStainless SteelMaterials and welding
- Corrosion-resistant steel, mostly austenitic grades 304/316 for piping. Pipe →
- STDStandard weightPipe and fittings
- Old weight class of pipe; equals Sch 40 up to NPS 10, and 9.53 mm (0.375 in) wall from NPS 12 upwards. Pipe →
- Steam trapProcess and instruments
- Device that drains condensate from steam lines without letting steam escape. Isometric symbols →
- Straight runUpstream / downstream straight lengthProcess and instruments
- Length of straight pipe needed before and after a flow element or control valve. Control valves →
- StrainerProcess and instruments
- Filter in a line to catch debris; Y-type, basket or temporary cone. Isometric symbols →
- Stress analysisLayout and supports
- Calculation of pipe stresses, support loads and nozzle loads (for example with CAESAR II). Expansion loops →
- Stress critical lineLayout and supports
- Line that must go through formal stress analysis, per the project criteria. Expansion loops →
- Stub endPipe and fittings
- Short pipe end with a flared lap, used with a loose lap-joint flange. Butt-weld fittings →
- Stub-inPipe and fittings
- Branch made by welding the branch pipe straight into a hole in the header, with or without a pad. Branch reinforcement →
- Stud boltFlanges and bolting
- Threaded rod with two nuts, the usual flange bolt in process piping. Flange joint →
- Stud lengthFlanges and bolting
- Length of stud bolt needed through both flanges, gasket and nuts, with thread protrusion. Flange joint →
- Support spanLayout and supports
- Distance between supports, limited by stress and deflection. Support spans →
- SurplusProject and general
- Extra quantity added to MTOs for waste and errors. MTO calculator →
- Sustained stressLayout and supports
- Stress from pressure and weight; primary and not self-limiting. Expansion loops →
- SWSocket WeldPipe and fittings
- Joint where the pipe sits in a socket and is fillet welded. Used for small bore; leave a 1.6 mm gap at the bottom. Socket weld & NPT →
- SwageSwage nipplePipe and fittings
- Forged small-bore reducer (MSS SP-95), with plain, bevelled or threaded ends. Socket weld & NPT →
- SweepoletPipe and fittings
- Contoured branch fitting with a smooth flow path, used in high-integrity service. Branch reinforcement →
- SWFSocket Weld flangeFlanges and bolting
- Small-bore flange with a socket for the pipe, fillet welded. Flanges →
- SWGSpiral Wound GasketFlanges and bolting
- Gasket of wound metal strip and filler (graphite or PTFE), with inner and outer rings (ASME B16.20). Gaskets →
- Swing checkValves
- Check valve with a hinged disc; suits horizontal and upward flow. Valves →
- SW (shop weld)Shop WeldDrawings and 3D
- Weld made in the fabrication shop; shown as a dot on isos. Isometric symbols →
T
- TBETechnical Bid EvaluationProject and general
- Comparison of vendor offers against requirements.
- TEThreaded EndPipe and fittings
- Pipe end threaded, usually NPT, for screwed joints. Socket weld & NPT →
- TeePipe and fittings
- Fitting with a branch at 90°. Equal tee: branch same size as run; reducing tee: smaller branch. Butt-weld fittings →
- Temporary strainerProcess and instruments
- Cone or plate strainer fitted for start-up and removed after commissioning. Isometric symbols →
- Test packTesting and construction
- Package of drawings and records for one pressure-test circuit.
- Test pressureTesting and construction
- Pressure applied during the strength test.
- Thermal expansionLayout and supports
- Growth of a pipe as its temperature rises (about 1.2 mm per metre per 100 °C for carbon steel). Expansion loops →
- ThreadoletPipe and fittings
- Olet with a threaded branch end. Branch reinforcement →
- Tie-inDrawings and 3D
- Connection of new piping to existing piping or equipment. Isometric symbols →
- TierLayout and supports
- One level of a pipe rack. Pipe rack →
- TI / TT / TWTemperature Indicator / Transmitter / ThermowellProcess and instruments
- Temperature instruments and the well protecting the sensor. P&ID symbols →
- TOE / TBEThreaded One End / Both EndsPipe and fittings
- Description of small-bore nipples and swages with threaded ends. Socket weld & NPT →
- TOPTop Of PipeLayout and supports
- Elevation of the top of a pipe. Pipe rack →
- TOSTop Of SteelLayout and supports
- Elevation of the top of a support beam. Pipe rack →
- TQTechnical QueryProject and general
- Formal technical question raised to the client or engineer.
- TrimValve trimValves
- The internal wetted parts of a valve that control flow: seat, disc, stem. Valves →
- TrunnionLayout and supports
- Pipe or plate welded to a pipe or elbow to transfer load to a support. Pipe supports →
- Two-phase flowProcess and instruments
- Gas and liquid flowing together; can cause slugging and vibration.
U
- U-boltLayout and supports
- U-shaped rod clamping a pipe to steel; acts as a guide or hold-down. Pipe supports →
- UFDUtility Flow DiagramDrawings and 3D
- Flow diagram for utilities such as steam, water and air. P&ID symbols →
- UnionPipe and fittings
- Threaded or socket-weld fitting that lets small-bore piping be dismantled without cutting. Socket weld & NPT →
- UnitProcess unitProject and general
- Section of a plant performing one process, such as a crude unit or SRU.
- UTUltrasonic TestingTesting and construction
- Inspection by ultrasound for weld defects or wall thickness.
- Utility stationHose stationProcess and instruments
- Point with air, water, steam and nitrogen hose connections for maintenance.
V
- Variable springLayout and supports
- Spring whose load changes with movement; for small movements. Pipe supports →
- VDRVendor Document RequirementsProject and general
- List of documents vendors must submit. Equipment data check →
- VDSValve Data SheetDrawings and 3D
- Data sheet defining a valve type, materials, ends and testing for procurement. Valves →
- VelocityProcess and instruments
- Speed of fluid in a pipe; limited to control erosion, noise and pressure drop.
- VendorSupplierProject and general
- Company supplying equipment or materials. Equipment data check →
- VTVisual TestingTesting and construction
- Visual inspection of welds and components.
W
- Water hammerSurgeProcess and instruments
- Pressure spike when flow stops suddenly, for example a fast-closing valve.
- Wear padLayout and supports
- Plate welded under a pipe at a support to protect the wall. Pipe supports →
- Weld mapMaterials and welding
- Drawing or list locating and numbering every weld for NDE and records. Iso compare →
- WeldoletPipe and fittings
- Olet with a butt-weld branch end. Branch reinforcement →
- WNWeld Neck flangeFlanges and bolting
- Flange with a tapered hub, butt welded to the pipe. Default for process service. Flanges →
- WPQWelder Performance QualificationMaterials and welding
- Test proving a welder can make sound welds to a WPS.
- WPSWelding Procedure SpecificationMaterials and welding
- Written procedure stating how a weld is to be made.
- WTWall ThicknessPipe and fittings
- Pipe wall thickness, set by the schedule or calculated from pressure, plus corrosion allowance and mill tolerance. Pipe →
X
Missing a term or see a mistake? Send it to us. See also the knowledge base and interview questions.
Contact & corrections
Questions, a value that differs from your edition of the code, or an idea for a new tool. For corrections, include the standard, table and size so the value can be checked.
Or email directly:
Isometric revision compare
Compare the issued (IFC) isometric against the latest from the model. Drop two PDFs for a linework overlay, or two PCF files for a component-by-component change list. Files stay in your browser.
Your drawings are never uploaded. The comparison runs entirely on your own computer, in this browser tab. No PDF or PCF file is sent to Pipe Ref or anyone else, and no file is saved. Close the tab and the files are gone.